Junior Instructor Electrician Previous Question paper
ย
ย
In this post, the Previous Question paper of Junior Instructor Electrician (Category Code: 726/2014) is given. The PDF can be downloaded at the last. You can watch the Detailed explanations in EEE Mae Easy Youtube Channel.
ย
The first 20 questions are removed as they were related to GK, Current Affairs and Renaissance. There will not be the GK section in any of the Technical Exams.
Question21:-
Recommended current density for a copper bus bar which is unenclosed should not exceed
ย
A:-165 A/sq. cm
B:-118 A/sq. cm
C:-178 A/sq. cm
D:-135 A/sq. cm
ย
Correct Answer:- Option-A
ย
Question22:-
In which type of winding, a long coil of sufficient length is firs wound and then inserted in one slot and the remainder of the length is turned and inserted in the adjacent slots?
ย
A:-Skein winding
B:-Involute coil winding
C:-Chain winding
D:-Basket winding
ย
Correct Answer:- Option-A
ย
Question23:-
If single phasing occurs during the running of a 3 phase induction motor, then
ย
A:-the motor may or may not run, will draw large current and the winding may burnout
B:-the motor may or may not run, will draw the normal current
C:-the motor will run normally
D:-the motor will stop
ย
ย
Correct Answer:- Option-A
Question24:-Buchholz relay operates on
A:-oil pressure
B:-gas pressure
C:-temperature
D:-current
ย
Correct Answer:- Option-B
ย
Question25:-
The cooling oil used in a transformer should have
ย
A:-to absorb moisture easily when exposed to air
B:-high insulation resistance
C:-low heat conductivity
D:-low firing point
ย
Correct Answer:- Option-B
ย
Question26:-
The maximum value of torque that a synchronous motor can develop without losing its synchronism is known as
ย
A:-breaking torque
B:-synchronising torque
C:-pull out torque
D:-pull in torque
ย
Correct Answer:- Option-C
ย
Question27:-
The transformer whose secondary is not isolated from the primary is
A:-current transformer
B:-potential transformer
C:-autotransformer
D:-step up transformer
ย
Correct Answer:- Option-C
ย
Question28:-
In the magneto-generator type insulation tester the handle is cranked at a speed of —— rpm approximately.
A:-1000 rpm
B:-1500 rpm
C:-750 rpm
D:-160 rpm
ย
Correct Answer:- Option-D
ย
Question29:-The light meter measures
ย
A:-luminance
B:-luminous intensity
C:-luminous flux
D:-illuminance
ย
Correct Answer:- Option-D
ย
Question30:-A servo voltage stabilizer provides a constant voltage to an accuracy around
A:-ยฑ1% to ยฑ0.5%
B:-0 to ยฑ1%
C:-ยฑ0.5% to ยฑ1.5%
D:-ยฑ1% to ยฑ1.5%
ย
Correct Answer:- Option-A
ย
Question31:-
Submersible pumps come under the category of
A:-centrifugal pumps
B:-jet pumps
C:-reciprocating pumps
D:-mono bloc pumps
ย
Correct Answer:- Option-A
ย
Question32:-
The size of the transformer used in the battery charger depends upon
A:-charging voltage of the battery
B:-charging power of the battery
C:-charging current capacity
D:-charging energy of the battery
ย
Correct Answer:- Option-B
ย
Question33:-According to IE rules, a clear space of not less than ——– in width shall be provided in front of the switchboard.
ย
A:-91.44 cm
B:-9.144 cm
C:-91.44 mm
D:-9.144 mm
ย
Correct Answer:- Option-A
ย
Question34:-To solder parts and terminals of medium size, the soldering iron used should be of
A:-30 W
B:-60 W
C:-80 W
D:-125 W
ย
Correct Answer:- Option-B
ย
Question35:-The size of binding wire used for binding insulator in overhead lines should not be less than
ย
A:-2 sq.mm
B:-1.5 sq.mm
C:-2.5 sq.mm
D:-1 sq.mm
ย
Correct Answer:- Option-A
Question36:-
The fusible plug fitted on the top of the electrical geyser casing is to
A:-disconnect the electrical supply in case of short circuit
B:-release the pressure inside the tank in case of thermostat failure
C:-fuse and release the steam inside the heater in case of overheat
D:-eject the 3 pin plug to disconnect the supply in case of earth fault
ย
Correct Answer:- Option-B
ย
Question37:-With the help of wheat stone bridge resistance in the range of ——– can be measured.
A:-0 to 1Kฮฉ
B:-10ฮฉ to 1Mฮฉ
C:-100ฮฉ to 10Mฮฉ
D:-1ฮฉ to 1Mฮฉ
ย
Correct Answer:- Option-D
ย
Question38:-
ย
The heat generated in a conductor by the flow of an electric current is proportional to the square of the current value, the resistance of the conductor and the time for which the current flows. This is stated by the law
A:-Ohm’s law
B:-Joule’s law
C:-Faraday’s law
D:-Murphy’s law
ย
Correct Answer:- Option-B
ย
Question39:-
In the case of double squirrel cage induction motors, the outer cage has
A:-high resistance and low reactance
B:-high resistance and high reactance
C:-low resistance and high reactance
D:-low resistance and low reactance
ย
Correct Answer:- Option-A
ย
Question40:-The property retentivity of material is useful on the construction of
A:-transformers
B:-electromagnets
C:-permanent magnets
D:-non magnetic substances
ย
Correct Answer:- Option-C
ย
Question41:-The leakage flux in a transformer depends upon
A:-load current, voltage, frequency and power factor
B:-load current, voltage, and frequency
C:-load current and voltage
D:-load current
ย
Correct Answer:- Option-D
ย
Question42:-
The slip rings of wound rotor machines are made from
A:-mild steel
B:-copper
C:-brass
D:-cast iron
ย
Correct Answer:- Option-C
ย
Question43:-In large generators, Hydrogen is used as
A:-conducting medium
B:-insulating medium
C:-insulating and cooling medium
D:-conducting and cooling medium
ย
Correct Answer:- Option-C
ย
Question44:-Highest power factor can be expected in which method of heating?
A:-Electric arc heating
B:-Dielectric heating
C:-Induction heating
D:-Resistance heating
ย
Correct Answer:- Option-D
ย
Question45:-Sulpher hexafluoride is used in
A:-Dynamos
B:-DC series motors
C:-Switch gears
D:-Synchronous motors
ย
Correct Answer:- Option-C
ย
Question46:-In an automobile electrical system, where alternators are used as a power source, the negative terminal is earthed, because
A:-to reduce corrosion
B:-to prevent damage to rectifiers and transistors
C:-to avoid electric shock
D:-to avoid damage to the alternator
ย
Correct Answer:- Option-B
ย
Question47:-Magnetic overload relays operate faster than bi-metallic relays because magnetic overload relays operate on
A:-current intensity
B:-voltage intensity
C:-thermal intensity
D:-power factor
ย
Correct Answer:- Option-A
ย
Question48:-3 phase squirrel cage induction motors with high slip, high starting torque and relatively low starting current are coming under the class of
A:-Class D motors
B:-Class C motors
C:-Class B motors
D:-Class A motors
ย
Correct Answer:- Option-A
ย
Question49:-Measuring instruments are classified based on their measuring accuracy. The precision and laboratory measuring devices come under the quality class of
A:-1.0
B:-0.3
C:-0.5
D:-1.5
ย
Correct Answer:- Option-B
ย
Question50:-A triac, when tested by an ohmmeter, will show a lower resistance in the order of 300 ohms between terminals
A:-MT 2 positive and G negative
B:-MT 1 positive and G negative
C:-MT 2 negative and G positive
D:-MT 1 positive and MT 2 negative
ย
Correct Answer:- Option-B
Question51:-_________ is the measure of how much potential difference the insulation layer can withstand without breaking down.
A:-Insulation resistance
B:-Breakdown voltage
C:-Resistance
D:-Dielectric strength
ย
Correct Answer:- Option-D
ย
Question52:-The light output of Tin oxide Sodium lamps is in the order of
A:-50 lumens/watt
B:-45 lumens/watt
C:-75 lumens/watt
D:-150 lumens/watt
ย
Correct Answer:- Option-D
ย
Question53:-The torque of a three-phase induction motor is proportional to
A:-square root of the applied voltage
B:-applied voltage
C:-square of the applied voltage
D:-half of the applied voltage
ย
Correct Answer:- Option-C
Question54:-Tap changing transformers are used for
A:-stepping up the voltage
B:-stepping down the voltage
C:-both stepping up and stepping down the voltage
D:-supplying low current for instruments
ย
Correct Answer:- Option-C
Question55:-Which Dc motor has a negligible effect on the speed with an increase in torque?
A:-DC differential compound motor
B:-DC cumulative compound motor
C:-DC series motor
D:-DC shunt motor
ย
Correct Answer:- Option-D
ย
Question56:-In a pure inductive AC circuit, the average true power is equal to
A:-V x I watts
B:-Zero watts
C:-Square of current multiplied by reactance Watts
D:-V x I volt-amperes
ย
Correct Answer:- Option-B
ย
Question57:-The part of an instrument which helps in leading in and leading out the current to the moving coil is
ย
A:-the spindle
B:-the copper or aluminium disc
C:-jewel bearing
D:-control spring
ย
Correct Answer:- Option-D
ย
Question58:-An outside micrometer can measure thickness and outside diameters to an accuracy of
A:-ยฑ0.1mm
B:-ยฑ0.5mm
C:-ยฑ0.001mm
D:-ยฑ0.01mm
Correct Answer:- Option-D
ย
Question59:-When a secondary battery is charged at 2% to 3% of normal rate for a long period, it is known as
A:-boost charge
B:-trickle charge
C:-freshening charge
D:-initial charge
ย
Correct Answer:- Option-B
ย
Question60:-Double squirrel cage induction motors are used where ________ torque is essential.
A:-high starting torque
B:-low starting torque
C:-low running torque
D:-high running torque
ย
Correct Answer:- Option-A
ย
Question61:-Which one of the following wiring circuit is not in accordance with IE rules?
A:-Corridor wiring
B:-Tunnel wiring
C:-Godown wiring
D:-Bank wiring
ย
Correct Answer:- Option-B
ย
Question62:-The distance between the two active sides of a coil under adjacent dissimilar poles is called
A:-coil pitch
B:-winding pitch
C:-pole pitch
D:-pitch factor
ย
Correct Answer:- Option-A
ย
Question63:-For the blocked rotor test of a 3 phase induction motor, the supply voltage should be limited to less than _______ percentage of rated voltage.
A:-5%
B:-10%
C:-3%
D:-20%
ย
Correct Answer:- Option-A
ย
Question64:-The amount of heat required to increase the temperature of one kilogram of water through 1ยฐC is
A:-3187 joule
B:-4187 joule
C:-4187 calorie
D:-3187 calorie
ย
Correct Answer:- Option-B
ย
Question65:-Admittance is the reciprocal of
A:-resistance
B:-conductance
C:-reactance
D:-impedance
ย
Correct Answer:- Option-D
ย
Question66:-The damping winding in a synchronous motor is generally used
A:-to provide starting torque only
B:-to reduce the noise level
C:-to prevent hunting and to provide the starting torque
D:-to reduce eddy currents
ย
Correct Answer:- Option-C
ย
Question67:-Voltage-dependent resistors are used as
A:-as current stabilizers
B:-as heating elements
C:-to suppress surges
D:-for inductive circuits
ย
Correct Answer:- Option-C
ย
Question68:-In a DC generator, brush shifting is done to
A:-alter the inter pole flux
B:-alter the main field flux
C:-neutralise the cross magnetizing effect
D:-neutralise the demagnetizing effect
ย
Correct Answer:- Option-C
ย
Question69:-To control a lamp from 4 positions, how many switches are required?
A:-4 two-way switches
B:-4 intermediate switches
C:-3 two-way switches and one intermediate switch
D:-2 intermediate switches and 2 two-way switches
ย
Correct Answer:- Option-D
ย
Question70:-The fusing factor for HRC fuse is
A:-2.0
B:-1.7
C:-1.4
D:-1.1
Correct Answer:- Option-D
ย
Question71:-Low and medium voltage underground cables should be laid at a depth of _______ from the ground surface to the top of the cable.
A:-0.75m
B:-0.9m
C:-1.0m
D:-1.05m
ย
Correct Answer:- Option-A
ย
Question72:-For low and medium voltage overhead lines, the minimum clearance above ground, which is erected across a street, shall not be less than
A:-5.791m
B:-6.096m
C:-5.486m
D:-4.572m
Correct Answer:- Option-A
ย
Question73:-In capacitor start, capacitor run motors, the capacitors used are
A:-both capacitors are of the same value
B:-one larger value capacitor of oil-filled type and a smaller value capacitor of electrolytic type.
C:-one larger value capacitor of electrolytic type and a smaller value capacitor of oil-filled type.
D:-both capacitors are of an electrolytic type.
Correct Answer:- Option-C
ย
Question74:-While erecting a pole, the depth of pit below the ground level, in normal soil should be about _________ of the length of the pole.
A:-1/6
B:-1/5
C:-1/4
D:-1/7
Correct Answer:- Option-A
ย
Question75:-In an AC operated relay, the purpose of shading coil placed near the tip of magnetic pole face is to
A:-eliminate chatter
B:-eliminate humming
C:-to reduce eddy current
D:-to reduce hysteresis loss
ย
Correct Answer:- Option-A
ย
Question76:-To test an armature for the short-circuited coils, ________ is used along with the growler.
A:-milli-voltmeter
B:-hacksaw blade
C:-ohm meter
D:-meggar
ย
Correct Answer:- Option-B
ย
Question77:-The type of fire extinguisher used where liquified gas is on fire is
A:-water filled fire extinguisher
B:-dry powder extinguisher
C:-foam type fire extinguisher
D:-carbon dioxide fire extinguisher
Correct Answer:- Option-B
ย
Question78:-Earthing one of the wires of electrical system, to limit the maximum voltage to earth under normal operating conditions is known as
A:-equipment earthing
B:-system earthing
C:-generator earthing
D:-substation earthing
Correct Answer:- Option-B
ย
Question79:-To measure the earth electrode resistance, the current and pressure spikes of the earth resistance tester are to be driven into the ground at a distance of ______ from the main electrode under test.
A:-20m and 10m apart respectively
B:-25m and 12.5m apart respectively
C:-20m and 10m apart respectively in a straight line
D:-25m and 12.5m apart respectively in a straight line.
Correct Answer:- Option-D
ย
Question80:-The type of joint used for overhead lines for tapping the electrical energy perpendicular to the service line is
A:-knotted tap joint
B:-aerial tap joint
C:-tee joint
D:-Britannia tee joint
Correct Answer:- Option-D
ย
Question81:-According to BIS and NEC, the clearance between the bottom point of the ceiling fan and the floor shall not be less than
A:-2.5m
B:-2.75m
C:-2.25m
D:-2.4m
Correct Answer:- Option-D
ย
Question82:-If firing angle in an SCR rectifier is increased, the output is
A:-remains same
B:-SCR is turned off
C:-decreased
D:-increased
Correct Answer:- Option-C
Question83:-Which electrode of the CRT mainly controls the brightness of the image on the screen?
A:-Anode
B:-Cathode
C:-Control grid
D:-Focusing electrodes
ย
Correct Answer:- Option-C
Question84:-The efficiency of a transformer is maximum, when
A:-no load loss is equal to full load loss
B:-hysteresis loss is equal to eddy current loss
C:-copper loss is equal to eddy current loss
D:-copper loss is equal to iron loss
Correct Answer:- Option-D
Question85:-For the parallel operation of two transformers, the phase sequence must be identical, otherwise, during the cycle
A:-when secondaries are loaded, it will produce unequal loading conditions
B:-impossible to take the full load output without excessive heating of one of the transformer
C:-each pair of phases will be open-circuited
D:-each pair of phases will be short-circuited
Correct Answer:- Option-D
ย
Question86:-A two-layer lap wound 4 pole generator with 16 coils will have a pole pitch of
A:-32
B:-16
C:-8
D:-4
Correct Answer:- Option-C
Question87:-The maximum safe temperature for class F insulating material is
A:-155ยฐC
B:-130ยฐC
C:-120ยฐC
D:-180ยฐC
Correct Answer:- Option-A
Question88:-The ratio of the intensity of magnetization to the magnetizing force is known as
A:-permeability
B:-permittivity
C:-susceptibility
D:-magnetic potential
Correct Answer:- Option-C
ย
Question89:-While testing the field coil connections by compass method, the DC voltage to be applied to the field coil is
A:-10 to 20% of rated voltage
B:-the rated voltage
C:-60 to 70% of rated voltage
D:-200% of rated voltage
ย
Correct Answer:- Option-A
ย
Question90:-The relays which are capable of maintaining their contacts in the last assumed position after the power is cut off are
A:-latching relays
B:-thermal relays
C:-reed relays
D:-electro-mechanical relays
Correct Answer:- Option-A
ย
Question91:-In large motor-generator sets, the AC motor used is usually
A:-squirrel cage type induction motor
B:-wound rotor type induction motor
C:-synchronous motor
D:-universal motor
ย
Correct Answer:- Option-C
ย
Question92:-A wattmeter measures the
A:-Apparent power
B:-Active power
C:-Reactive power
D:-Power factor
ย
Correct Answer:- Option-B
Question93:-A series resonant circuit is known as acceptor circuit because its ______ will be maximum
A:-voltage
B:-current
C:-power factor
D:-frequency
Correct Answer:- Option-B
ย
Question94:-With a two-watt meter method of 3 phase power measurement, if one wattmeter gives a negative indication, then, the power factor will be
A:-unity
B:-zero
C:-more than 0.5
D:-less than 0.5
Correct Answer:- Option-D
ย
Question95:-A moving coil milliammeter having a resistance of 10 ohm gives full scale deflection, when a current of 5mA is passed through it. If the instrument to be used to measure a current up to 1A, then
A:-a resistance of 0.502 ohm must be connected in series with the ammeter
B:-a resistance of 0.502 ohm must be connected in series with the load
C:-a resistance of 0.502 ohm must be connected in parallel to the ammeter
D:-a resistance of 0.502 ohm mus be connected in parallel to the load
Correct Answer:- Option-C
ย
Question96:-The instrument which give the value of the quantity to be measured in terms of deflection and instrument constants are
A:-secondary instruments
B:-indicating instruments
C:-integrating instruments
D:-absolute instruments
Correct Answer:- Option-D
Question97:-A measuring instrument is enclosed inside an iron case. This is for protecting the measuring mechanism from
A:-heat
B:-magnetic flux
C:-static electricity
D:-hysteresis effect
Correct Answer:- Option-B
Question98:-The cell voltage of a Lithium cell is
A:-2.1 to 2.6V
B:-2.5 to 3.6V
C:-1.2 to 1.4 V
D:-1.5V
Correct Answer:- Option-B
ย
Question99:-The illumination is directly proportional to the cosine of the angle made by the normal to the illuminated surface with the direction of the incident flux. This statement is associated with
A:-Macbeth’s law of illumination
B:-Bunsen’s law of illumination
C:-Lambert’s cosine law
D:-Plank’s law
Correct Answer:- Option-C
ย
Question100:-In a drill, ______ helps to form the cutting edge.
A:-Land
B:-Shank
C:-Tang
D:-Flutes
Correct Answer:- Option-D
ย
ย
ย
ย
ย
ย
Join EEE Made Easy Whatsapp Channel
- [PDF] Syllabus Workshop Instructor Tool and Die|242/2023 syllabus Kerala PSC
- [PDF]Junior Instructor Technician Mechatronics Syllabus|654/2023 syllabus Kerala PSC
- [PDF]Tracer in Soil Survey and Soil Conservation Syllabus|600/2023 Syllabus Kerala PSC
- [PDF] Junior Instructor Fitter Syllabus|659/2023 syllabus Kerala PSC
- [PDF] Junior Instructor Turner Syllabus|661/2023 Syllabus Kerala PSC
- [PDF] Technical Supervisor Travancore Sugars and Chemicals Syllabus|693/2023 syllabus Kerala PSC
- [PDF]AE Electrical Universities Syllabus|070/2024 syllabus Kerala PSC
